Application of a modified generalized sail model on a solar sail with wrinkles

In this paper, we present an analysis of effect of wrinkles on the solar sail performance. We describe different analytical, semi-analytical and numerical approaches to the calculation of general large-scale curvature of a solar sail as well as parameters of so-called wrinkled domains, and introduce the impact of such wrinkles on the thrust and torque of the solar sail. Finally, we present a model of an optically-orthotropic surface for such non-ideal sail, providing a connection with the Generalized Sail Model, and other solar sail thrust models.     

高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

弹载变转速定量泵高动态压力控制特性分析

传统弹载电液伺服系统的液压能源采用有刷直流电机驱动恒压变量泵的方式，泵源压力在导弹飞行过程中设定值恒定，但在平飞段过程长、负载小，对能源压力需求低，造成弹上能源总利用率不高的问题，提出无刷直流电机驱动小排量液压泵的压力控制泵源的设计，在低气动负载阶段适当降低系统压力，进而降低节流损失与泄漏量，提高能量利用率。分析了变转速定量泵的流量压力特性曲线，通过建立基于变转速压力控制泵源的位置电液伺服系统数学模型与仿真模型，分析了变转速定量泵压力控制系统在典型工况下的位置跟踪、系统压力变化与能量利用效率，验证了压力控制系统能够在导弹平飞段保证位置伺服系统跟踪正常的前提下，能有效提高系统效率，证明了变转速定量泵压力控制系统的有效性与可行性。     

前缘缝翼构型平尾直升机气动特性分析

使用数值模拟方法研究了前缘缝翼翼型气动特性,并将该前缘缝翼翼型应用于直升机平尾,分析了该直升机全机气动特性,最后通过风洞试验对数值模拟结果进行验证。结果表明,前缘缝翼构型平尾能有效改善直升机的纵向静稳定性。     

非恒定增压式微尺度拉瓦尔喷管流动特性

针对微尺度喷流在航天器运动状态切换时出现的非恒定增压变化,采用直接模拟蒙特卡洛(DSMC)方法对阶跃式增压和线性式增压两种模式下的微尺度拉瓦尔喷管流场进行了模拟,并对其变化过程中的流动特性进行了对比分析。结果显示：阶跃式增压会导致流动特性出现较大幅值的峰谷式波动,而线性式增压下的流动特性则呈现出线性变化的特点;黏性力对微尺度喷流的非恒定增压变化产生了重要的黏滞作用,在喉部扩张段至出口的流场中尤为明显;在设定的条件下,阶跃式增压过程中喷流产生的总冲量较线性式增压高59.5%,质量流量高74.7%,单位工质提供的冲量低约8.6%,波动性也高于线性式模型,阶跃式增压适用于系统需要较大推力改变运动状态且推进剂充足的情况,而线性式增压在系统精确微调或需要推进剂产生更高效能时具有明显的优势。     

多种工质下螺旋波等离子体源波场结构数值模拟

针对螺旋波等离子体放电机理，开展了多种工质条件下的螺旋波放电等离子体内波场结构数值模拟研究。计算发现:氦气等离子体的Er分量在径向边界处的峰值更为突出，有利于等离子体在径向的输运，波电场径向分量决定了电流密度径向分量在内部的表现。在0.266 Pa和1.064 Pa两种气体压强条件下，通过波场结构验证了气压对于波阻尼影响的结论。波场结构是螺旋波在等离子体内传播以及能量沉积的微观体现，研究螺旋波波场结构是揭示其高电离效率的重要途径。初步探索了功率耦合机制，为实验系统优化及实验方案设定奠定理论基础。     

An empirical solar radiation pressure model for satellites moving in the orbit-normal mode

We present a family of empirical solar radiation pressure (SRP) models suited for satellites orbiting the Earth in the orbit normal (ON) mode. The proposed ECOM-TB model describes the SRP accelerations in the so-called terminator coordinate system. The choice of the coordinate system and the SRP parametrization is based on theoretical assumptions and on simulation results with a QZS-1-like box-wing model, where the SRP accelerations acting on the solar panels and on the box are assessed separately. The new SRP model takes into account that in ON-mode the incident angle of the solar radiation on the solar panels is not constant like in the yaw-steering (YS) attitude mode. It depends on the elevation angle of the Sun above the satellite’s orbital plane. The resulting SRP vector acts, therefore, not only in the Sun-satellite direction, but has also a component normal to it. Both components are changing as a function of the incident angle. ECOM-TB has been used for precise orbit determination (POD) for QZS-1 and BeiDou2 (BDS2) satellites in medium (MEO) and inclined geosynchronous Earth orbits (IGSO) based on IGS MGEX data from 2014 and 2015. The resulting orbits have been validated with SLR, long-arc orbit fits, orbit misclosures, and by the satellite clock corrections based on the orbits. The validation results confirm that—compared to ECOM2—ECOM-TB significantly (factor 3–4) improves the POD of QZS-1 in ON-mode for orbits with different arc lengths (one, three, and five days). Moderate orbit improvements are achieved for BDS2 MEO satellites—especially if ECOM-TB is supported by pseudo-stochastic pulses (the model is then called ECOM-TBP). For BDS2 IGSOs, ECOM-TB with its 9 SRP parameters appears to be over-parameterized. For use with BDS2 IGSO spacecraft we therefore developed a minimized model version called ECOM-TBMP, which is based on the same axis decomposition as ECOM-TB, but has only 2 SRP parameters and is supported by pseudo-stochastic parameters, as well. This model shows a similar performance as ECOM-TB with short arcs, but an improved performance with (3-day) long-arcs. The new SRP models have been activated in CODE’s IGS MGEX solution in Summer 2018. Like the other ECOM models the ECOM-TB derivatives might be used together with an a priori model.     

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

强不确定系统“全系数之和等于1”的实现方法

摘要： 研究强不确定系统“全系数之和等于1”的实现方法，强不确定系统指的是系统的静态增益及其界不完全确知且范围较大.“全系数之和等于1”是吴宏鑫院士20世纪80年代发现的，该原理表明，对于未知连续系统，其离散化系统的系数的和在一定条件下是1.该原理的发现对于解决闭环辨识和自适应控制的瓶颈问题具有关键作用.“全系数之和等于1”是在一定条件下成立的.为了实现系统的“全系数之和等于1”，需要对系统进行一定的变换，以满足所需条件.其中，采用静态增益的标称值的倒数进行输入变换的方法在实际中得到了广泛应用.但是，当系统的不确定性较大时，该变换将带来较大偏差.针对该问题开展了深入研究，明确给出了系统静态增益的不确定性与标称值的比值的关系对于实现“全系数之和等于1”的影响.当不确定性与标称值的比值较小时，可以近似实现“全系数之和等于1”；当比值较大时，进一步给出了通过选取合适的采样周期，近似实现“全系数之和等于1”的方法.本文的研究对于特征模型理论在实际中的应用提供了一定的基础.     

The adjusted optical properties for Galileo/BeiDou-2/QZS-1 satellites and initial results on BeiDou-3e and QZS-2 satellites

Solar Radiation Pressure (SRP) is the dominant non-gravitational perturbation for GNSS (Global Navigation Satellite System) satellites. In the absence of precise surface models, the Empirical CODE Orbit Models (ECOM, ECOM2) are widely used in GNSS satellite orbit determination. Based on previous studies, the use of an a priori box-wing model enhances the ECOM model, especially if the spacecraft is a stretched body satellite. However, so far not all the GNSS system providers have published their metadata. To ensure a precise use of the a priori box-wing model, we estimate the optical parameters of all the Galileo, BeiDou-2, and QZS-1 (Quasi Zenith Satellite System) satellites based on the physical processes from SRP to acceleration. Validation using orbit prediction proves that the adjusted parameters of Galileo and QZS-1 satellites exhibit almost the same performance as the corresponding published and “best guess” values. Whereas, the estimated parameters of BeiDou-2 satellites demonstrate an improvement of more than 60% over the initial “guess” values. The resulting optical parameters of all the satellites are introduced into an a priori box-wing model, which is jointly used with ECOM and ECOM2 model in the orbit determination. Results show that the pure ECOM2 model exhibits better performance than the pure ECOM model for Galileo, BeiDou-2 GEO and QZS-1 orbits. Combined with the a priori box-wing model the ECOM model (ECOM+BW) results in the best Galileo, BeiDou-2 GEO and QZS-1 orbits. The standard deviation (STD) of satellite laser ranging residuals reduce by about 20% and 5% with respect to the pure ECOM2 model for Galileo and BeiDou-2 GEO orbits, while the reductions are about 40% and 60% for QZS-1 orbits in yaw-steering and orbit-normal mode respectively. BeiDou-2 IGSO and MEO satellite orbits do not benefit much from the a priori box-wing model. In summary, we suggest setting up a unified SRP model of ECOM+BW for Galileo, QZS-1, and BeiDou-2 orbits based on the adjusted metadata. In addition, we estimate the optical parameters of BeiDou-3e and QZS-2 satellites using a limited number of tracking stations. Results regarding the unified SRP model indicate the same advantages, the STD of satellite laser ranging residuals reduces by about 30% and 20% for QZS-2 and BeiDou-3e orbits respectively over orbit products without a priori model. The estimation procedure is effective and easy to apply to the new emerging satellites in the future.